Product Name: High Activity Amino-Modified Rigid Foam Silicone Oil
Product Code: HAA-RFSO
Chemical Family: Organosiloxane Compound
Recommended Uses: Additive in foam manufacturing for insulation materials
Manufacturer: Refer to product label for supplier details
Emergency Contact: Access local poison control or emergency service numbers
Classification: Not classified as hazardous under GHS standards
Primary Hazards: Mild skin and eye irritation possible after direct contact; untested for chronic effects
Signal Word: Caution
Hazard Statements: May cause slight irritation to eyes or skin. Prolonged inhalation of vapors may cause dizziness or headache.
Precautionary Statements: Use adequate ventilation. Avoid splashing or misting. Wear eye protection. Wash hands after use. Keep away from food and drink.
Chemical Identity: Polydimethylsiloxane, amino-functionalized
CAS Number: 63148-62-9
Concentration: ~100%
Impurities: <1% proprietary stabilizers or by-products possible
Eye Contact: Rinse immediately with plenty of water for 15 minutes. Remove contact lenses. Seek medical help for any persistent irritation.
Skin Contact: Remove contaminated clothing. Wash affected area with soap and water. Seek medical attention if signs of irritation persist.
Inhalation: Move person to fresh air. Support breathing as needed. If symptoms such as headache or dizziness develop, call a doctor.
Ingestion: Rinse mouth. Never give anything by mouth to an unconscious person. Get medical assistance if large quantities are swallowed.
Suitable Extinguishing Agents: Water spray, foam, dry chemical powder, carbon dioxide
Specific Hazards: Siloxane vapors may form toxic gases under fire conditions. Decomposition could release formaldehyde, carbon oxides, or silicon dioxide.
Protective Equipment for Firefighters: Use self-contained breathing apparatus and full protective clothing. Keep upwind of fire site. Cool fire-exposed containers with water.
Personal Precautions: Ventilate area. Evacuate unnecessary personnel. Wear chemical-resistant gloves, splash goggles, and appropriate clothing.
Environmental Protection: Prevent entry into sewers, drains, and surface water. Inform authorities if large quantities enter the environment.
Cleanup Methods: Absorb with inert absorbent (e.g., sand, vermiculite). Collect in labeled waste containers. Wash area with detergent and water.
Safe Handling: Avoid contact with eyes and skin. Use only with adequate ventilation. Do not eat, drink, or smoke around product.
Storage Conditions: Store in original, tightly-sealed containers in a cool, dry location. Avoid exposure to direct sunlight and moisture. Keep away from incompatible substances such as strong oxidizers and acids.
Incompatible Materials: Avoid storage with peroxides, strong acids, or alkali.
Exposure Limits: No established occupational exposure limits for major constituents
Engineering Controls: Use local exhaust ventilation when handling large volumes or at elevated temperatures.
Personal Protective Equipment: Wear chemical-resistant gloves, splash-proof safety goggles, and protective clothing. In cases of insufficient ventilation, use organic vapor respirator.
Hygiene Measures: Wash hands thoroughly before eating or drinking. Clean protective equipment before reuse.
Appearance: Clear to slightly hazy, viscous liquid
Odor: Mild, slightly amine-like
Odor Threshold: Not determined
pH: Not applicable
Melting/Freezing Point: Below -50°C
Boiling Point/Range: >200°C
Flash Point: >250°C (closed cup)
Evaporation Rate: Negligible
Flammability: Not highly flammable
Vapor Pressure: <1 mm Hg at 25°C
Vapor Density: Heavier than air
Solubility in Water: Insoluble
Partition Coefficient (n-octanol/water): No data available
Auto-Ignition Temperature: >400°C
Decomposition Temperature: >250°C
Viscosity: 500–2000 cSt (product dependent)
Chemical Stability: Stable under recommended storage conditions.
Possible Hazardous Reactions: Reacts with strong oxidizers or acids; can release hazardous fumes if strongly heated or burned.
Conditions to Avoid: Excessive heat, sparks, prolonged UV light exposure, incompatible substances.
Hazardous Decomposition Products: Silicon dioxide, formaldehyde, carbon monoxide, carbon dioxide.
Polymerization: No hazardous polymerization expected.
Likely Routes of Exposure: Skin and eye contact, inhalation of aerosols or vapor.
Acute Toxicity: Low hazard under routine handling; may cause irritation to skin or eyes.
Chronic Toxicity: No data indicating long-term adverse effects in humans.
Carcinogenicity: Ingredients are not listed by IARC, NTP, or OSHA as carcinogens.
Other Effects: Prolonged or repeated exposure could exacerbate pre-existing skin or respiratory conditions.
Toxicity to Aquatic Life: Not expected to be acutely toxic; limited data on chronic aquatic effects.
Persistence and Degradability: Not readily biodegradable; may degrade slowly in soil and water.
Bioaccumulation Potential: Low based on structure and water solubility.
Mobility in Soil: Product expected to remain predominantly immobile due to viscous, insoluble nature.
Other Adverse Effects: Avoid discharge to the environment; contain spills.
Waste Treatment Methods: Dispose of material at a licensed facility according to local, regional, or national regulations.
Container Handling: Drain and triple rinse drums or pails before recycling or disposal. Do not release residue to environment.
Special Precautions: Prevent bulk release; incineration may be suitable if permitted by authorities.
UN Number: Not regulated as dangerous good
UN Proper Shipping Name: Non-hazardous for transport
Transport Hazard Class: N/A
Packing Group: N/A
Environmental Hazards: Product not anticipated to pose significant hazard to aquatic environments in normal carriage.
Transport Precautions: Ship in secure, sealed containers; avoid damage or leakage.
Workplace Safety: Observe local chemical safety regulations; ensure worker training for handling silicone oils.
OSHA Status: Not specifically regulated as a hazardous material under OSHA standards.
SARA Title III Sections 311/312: Does not qualify for reporting as hazardous.
Canadian WHMIS: Not classified as hazardous.
REACH Information: All main ingredients pre-registered or exempted.
Other Requirements: Include product in company Health and Safety documentation and provide access to MSDS for personnel.
